The Grip for Motorbunny Buck: Using Fleshlight Strokers
By Motorbunny - New Riding Sex Toys and Sex Machines | Published: 2026-10-14
Category: ハウツーガイド
Learn how to mount and use The Grip for Motorbunny BUCK with standard Fleshlight strokers. Step-by-step setup, technique, and cleanup for hands-free thrusting.
Quick answer
Mount The Grip for Motorbunny BUCK by sliding it onto the BUCK's thrusting arm and locking the pull-tab lever, then insert any standard Fleshlight stroker. Use low thrust speed first to confirm the stroker stays seated, and always clean both the Grip and the stroker sleeve after use.
Why The Grip changes the BUCK experience
The Grip for Motorbunny BUCK flips the script on the world's most versatile vibrator by letting you use standard Fleshlight strokers with the machine's thrusting mechanics. Instead of holding a stroker by hand, you lock it into the Grip and let BUCK do the work. This is a different feel from a standard attachment because the stroker sleeve provides its own texture and suction, while BUCK adds consistent thrusting and vibration. The result is hands-free stimulation that combines the sleeve you already like with the machine's power.
Check your stroker before you mount anything
The Grip is designed to firmly support any standard Fleshlight stroker, but not every stroker has the same outer case dimensions. Before you start, confirm your stroker uses a standard hard outer case. If you are using a Main Squeeze stroker such as the Main Squeeze Scarlit Scandal ULTRASKYN Stroker Pussy Carmael or the Main Squeeze Belladonna Pussy, those have their own hard cases with squeeze plates and twist bases that may not fit the same way a Fleshlight case does. The Grip's pull-tab locking lever is built around the Fleshlight form factor, so a non-standard case can feel loose or fail to seat. When in doubt, test the fit with the machine off before adding lube or turning on thrust.
Set up your space and power down
Place BUCK on a stable, flat surface and turn it off before mounting anything. Have your stroker, water-based lubricant, and a towel within reach. The Grip mounts in one easy step, but you still want a clear workspace so you can see the locking lever and confirm it engages. If you are using a Fleshlight stroker, remove the outer cap if it interferes with the mount, and keep the sleeve inside its case. Do not apply lube to the Grip itself; lubricant goes inside the stroker sleeve only.
Match thrust speed to the stroker
BUCK's thrusting mechanics are exclusive to BUCK, and they can be more intense than vibration alone. Start with the lowest thrust setting and a low vibration level, then increase one variable at a time. A heavier or fuller stroker sleeve may need a slower thrust speed to stay seated, while a tighter sleeve may feel better with more vibration and less thrust. If the stroker shifts or the Grip feels like it is working loose, stop and reseat it rather than pushing through.
Step-by-step: mounting and using The Grip
- Power down and stabilize BUCK: Turn BUCK off and place it on a flat, stable surface. Clear the area around the thrusting arm so you can see the mount point and the pull-tab locking lever. Checkpoint: the machine should not move when you press down on the arm.
- Slide The Grip onto the thrusting arm: Align The Grip with the BUCK thrusting arm and slide it on in one easy step. Press the pull-tab locking lever until it clicks or seats fully. Common mistake: forcing the Grip on at an angle. If it does not slide freely, pull it off and realign.
- Insert your Fleshlight stroker: With the machine still off, push a standard Fleshlight stroker into The Grip until it sits firmly. The Grip is designed to support any standard Fleshlight stroker, so the case should not wobble. Checkpoint: give the stroker a gentle tug. If it shifts, reseat it before adding lube.
- Lubricate the sleeve, not the Grip: Apply water-based lubricant inside the stroker sleeve. Keep lubricant off the Grip's locking lever and mounting surfaces so the lock stays secure. Common mistake: over-lubricating, which can make the stroker slide in the Grip. Use a modest amount and add more only if needed.
- Start low and test the thrust: Turn BUCK on at the lowest thrust and vibration settings. Let it run for a few strokes while you watch the stroker's position. Checkpoint: if the stroker moves or the Grip loosens, stop and reseat before increasing speed.
- Adjust one variable at a time: Increase thrust or vibration separately. A tighter sleeve often feels better with more vibration and less thrust; a looser sleeve may handle more thrust. Common mistake: maxing out both settings at once, which makes it hard to tell what needs adjusting.
- Stop, remove, and clean everything: Turn BUCK off before removing the stroker. Take the stroker out of The Grip, then remove The Grip from the arm. Clean the stroker sleeve according to its maker's instructions, and wipe The Grip with a toy cleaner or mild soap and water. Next step: let all parts dry fully before storing them, and check the locking lever for residue before your next session.
Product facts
- The Grip for Motorbunny BUCK - Fits Fleshlight Strokers: The Grip for Motorbunny BUCK is designed to firmly support any standard Fleshlight Stroker and mounts in one easy step with a pull-tab locking lever. You can use strokers you already own instead of buying a proprietary attachment, and the lever makes setup quick enough to change sleeves mid-session.
- Main Squeeze Scarlit Scandal ULTRASKYN Stroker Pussy Carmael: Main Squeeze Scarlit Scandal ULTRASKYN Stroker Pussy Carmael is molded directly from Scarlit Scandal with a hard outer case and a squeeze plate. Its case and squeeze plate are part of the stroker's function, so check whether that case shape seats in The Grip before relying on it for a hands-free session.
- Main Squeeze Belladonna Pussy: Main Squeeze Belladonna Pussy has a hard outer case with a built-in squeeze plate grip and a base that twists to adjust suction strength. The twist base adds suction control, but that same base may change how the stroker sits in The Grip, so test the fit with the machine off first.
