How to Set Up a Motorbunny BDSM Restraints Scene Safely
By Motorbunny - New Riding Sex Toys and Sex Machines | Published: 2026-10-14
Category: Guide pratiche
Plan and run a bondage scene with your Motorbunny using the BDSM Restraints. Step-by-step setup, safety checks, and common mistakes to avoid.
Quick answer
To set up a safe Motorbunny BDSM restraints scene, first secure the machine, then attach the restraints to the eyelet, adjust cuffs for circulation, and agree on a safe word. Always check that the unit cannot tip before adding any restraint tension.
Why restraint setup differs from a standard riding session
When you add restraints, you change the physics and the power dynamic. The Motorbunny becomes an anchor point, so any pull on the cuffs transfers directly to the machine. That means you need to treat the setup as a two-part safety system: the machine must be stable, and the restraints must be adjusted so they don’t restrict breathing or blood flow. The BDSM Restraints are designed to clip to the Motorbunny eyelet, but they don’t replace a stable surface. Test the machine’s stability before you attach anything.
Pre-scene checks: body, space, and gear
Before any bondage play, run through a quick checklist. Clear the floor of sharp objects or pet hair that could interfere with the machine’s base. Have safety shears within reach even if you use quick-release clips. Discuss limits and agree on a safe word or signal. If you’re using the restraints on a partner, confirm they can still communicate and that the cuffs are not too tight. The BDSM Restraints have a soft vegan leatherette cuff with faux-fur liner, which helps reduce friction, but you still need to check for numbness or discoloration during use. Never leave a restrained person alone.
Step-by-step: Motorbunny BDSM restraints setup
- 1. Secure the Motorbunny unit: Place the Motorbunny on a flat, stable surface. If it has suction cups or a base, press down firmly. Check that it does not wobble when you push it from the top. Common mistake: skipping this step and relying on the restraints to hold the machine down. The restraints are not a substitute for a stable base.
- 2. Locate the eyelet and clip the restraints: Find the eyelet on your Motorbunny. Clip the BDSM Restraints onto the eyelet. Make sure the clip is fully closed and cannot slip off. Checkpoint: tug gently on the strap to confirm the clip is secure before moving on.
- 3. Adjust the cuffs before restraining: Open the cuffs and adjust the extendable straps to a loose starting point. You should be able to slide two fingers under the cuff. The faux-fur liner should sit against the skin, not the leatherette edge. Common mistake: tightening cuffs too much before the scene starts. You can always tighten later, but starting too tight risks numbness.
- 4. Position your partner and attach cuffs: Have your partner sit or lie in the desired position on the machine. Attach the cuffs to their wrists or ankles, then connect the cuffs to the restraint straps. Keep the straps slack until you’re ready to apply tension. Checkpoint: ask your partner to wiggle their fingers or toes. If they can’t, the cuffs are too tight.
- 5. Apply tension gradually and check circulation: Slowly shorten the straps to take up slack. Stop when you feel light resistance. Do not pull the straps taut. During the scene, check hands and feet every 10–15 minutes for color, temperature, and sensation. Common mistake: pulling straps tight enough to restrict movement completely. A little slack lets your partner adjust and keeps circulation safe.
- 6. Run a final safety check and start the scene: Confirm the safe word, make sure safety shears are within reach, and verify the machine is still stable. Turn on the Motorbunny and begin at a low setting. Increase only after checking in with your partner. Checkpoint: if the machine shifts or tips at any point, stop immediately and reset the base before continuing.
Product facts
- BDSM Restraints: The BDSM Restraints clip to the Motorbunny eyelet and have extendable straps with soft vegan leatherette cuffs and faux-fur liners. They are one size fits all and compatible with all Motorbunny units. The clip-on design means you can add or remove restraints quickly, and the extendable straps let you adjust tension without unclipping. The faux-fur liner reduces the chance of skin irritation during longer scenes.
